How Do U Make a Mousetrap Car Go Faster

Download Article

Download Article

You can purchase kits online that provide you with all the parts necessary to put together a mousetrap racer. However, most mousetrap racers are built to travel as far as possible, not as fast as possible. Most adaptations you make to a racer will not increase max speed, but rather acceleration, usually at the expense of distance. In other words, if speed is your goal, you will need to adapt your racer to travel shorter distances quicker.^[1]

1. 1

   Shorten the lever arm. Installing a shorter lever arm is the best way to adapt a racer for speed. However, if the lever is too short, it will spin out. There is no precise formula for how long the lever should be. Experiment to see how short you can get the lever while maintaining control of the car.^[2]

   • Longer lever arms will extend the time in which the axle is pulled, making it travel longer distances before the car reaches maximum speed. As a result, it will go slower, but move further.^[3]

2. 2

   Find smaller wheels. When you increase the size of the wheel, the amount of torque necessary to begin a rotation increases as well. A smaller wheel is easier to turn. So you should make sure that your driving (front) wheel is as small as possible. A good standard is approximately 3 inches (7.6 cm) in diameter.^[4]

   • Use materials that are as lightweight as possible.
   • A larger wheel means more rotational inertia, which keeps the wheel moving once it gets going, but reduces acceleration.
   • A smaller wheel is a trade-off between distance and speed. The overall distance traveled will decrease as you reduce the size of the driving wheel. Experiment to determine what the most functional design is.

   Advertisement

3. 3

   Increase the size of the axle. The greater the ratio of the diameter of the axle to the wheel, the less force will be required to accelerate the car. In other words, you should match a larger axle with a smaller wheel to increase acceleration.

   • Conversely, a mousetrap racer built for distance should have a smaller axle and a larger driving wheel.^[5]
   • One way to adapt the size of the axle is to wrap tape around the center of the axle, where it does not come into contact with the frame. This added weight will increase the torque of the axle.^[6]
   • Experiment to find the correct amount of torque by adding and removing layers of tape.

4. 4

   Increase traction. For the wheel to pick up speed it needs to create pressure against the ground. For the wheel, use a material with a rough texture around the outside to give the wheel traction. Alternatively, cut something that has a rough surface such as a rubber balloon. Glue strips of this material to the outside of the wheel to give it traction.^[7]

5. 5

   Keep on trying. There are so many variables involved in the physics of a mousetrap racer that even similarly built cars operate differently. The only way to perfect your model is to experiment with small variations in design to determine what works best.

   • Study mousetrap racers that have won competitions in the past. Learn from designs that you know work.^[8]

   Advertisement

1. 1

   Reduce weight. Reducing the weight will lower rolling friction with the ground. Trim the deck down so it is only as large as necessary to support the mousetrap. When gluing down the deck, put it as close to the back wheels as possible without touching them.

   • Drill holes in nonessential components to reduce weight. Consider drilling holes in the frame and the wheels as well.^[9]
   • The material used for the frame of the car should be as lightweight and as rigid as possible. Consider bamboo, balsa wood, or foam.
   • Use glue whenever you need to attach something. Tape can be used too, but glue is smoother and weighs less. Don't use metal bolts, however; they add weight.

2. 2

   Cut down on the number of pulleys and gears. A complicated system of gears and pulleys can be useful when building a racer for distance, because they increase the overall torque. However, when building for speed, they principally serve to create more friction between the components. Consider connecting the lever directly to the axle when building a car for speed.^[10]

3. 3

   Limit air resistance. As speed increases, so too does air resistance, making it a progressively more likely to stop your car in its tracks. To prevent this from happening, make sure that as little surface area as possible is exposed. Experiment with different materials for frames to see what is most aerodynamic.

   • If you are using a wood frame, sand it and paint it. This will make it more aerodynamic.^[11]
   • Similarly, reduce the surface area of the car to reduce air resistance. For example, find a thinner frame and wheels.

4. 4

   Eliminate friction between the axle and the frame. Your car can lose a lot of energy at the point where the axle touches the frame. Watch these surfaces to see if the axle seems to get stuck. Try applying a lubricate, like graphite powder. Alternatively, redesign the axle. Consider installing ball bearings.^[12]

   • You can search online for a chart of coefficients of friction, to determine which materials have the least friction when paired.

   Advertisement

Add New Question

• Question

  Is it difficult to make a mousetrap car?

  

  It depends on the materials used and strategies for creating one. There are thousands of different types of mousetrap cars. If you just want a simple one that goes a few feet, it is fairly easy.

• Question

  If I use the balloons, will the car go less distance?

  

  Not if you use them properly. Balloons give traction and are only useful on the rear or powered wheels. Adding balloons or rubber bands to the front would increase friction and slow the car.

• Question

  What are the differences between a mousetrap car that has to do with speed and one that has to do with distance?

  

  A speedy mousetrap car will have smaller wheels (faster acceleration), a shorter lever arm (increased torque, but smaller travel distance), a larger axle (increased acceleration) and will generally be smaller to decrease air resistance. A mousetrap car built for distance will have larger wheels (travels a longer distance per turn), a longer lever arm (increase the distance the car is able to travel), a smaller axle (delivers more torque to the drive wheels) and may be larger, due to the larger size of the wheels.

• Question

  How do I make a car mousetrap go farther?

  

  Use a longer pole/stick attached to the mousetrap's hammer. A longer stick allows more string to be used, and makes it go slower, not faster.

• Question

  When you put a big wheel on the back, why would you not put it in the front, too?

  

  Having bigger back wheels and smaller front wheels is like going downhill, so it makes it go faster.

• Question

  Can you use wood for the body of the car?

  

  Yes. The article states, "If you are using a wood frame, sand it and paint it. This will make it more aerodynamic."

• Question

  Will it travel at least one meter?

  

  Yes, it will. if you follow all of these steps correctly, it should go much more than just one meter!

• Question

  Are three or four wheels better for speed or distance?

  

  Three is better for everything in this case, reducing weight and rolling resistance. The only downside is that it makes design harder, since you need to extend the chassis either forward or under the trap to mount it.

• Question

  How can I make the car go backwards?

  

  Attach an axle hook to the drive axle. (This can be in the form of a zip tie or a piece of metal.) First, wind the string so that the wheels are spinning forward. (This is the string that will propel the vehicle backwards.) After winding the amount needed to travel backwards, loop the string around the axle hook and wind it in the opposite direction so that the wheels are spinning backwards. This is also the string that will power the vehicle forwards.

• Question

  Why should I use small wheels if bigger wheels travel more distance per rotation, and speed is just how much distance I can cover in a certain amount of time, or how much time it takes for me to cover a distance? And why are big axles needed as well?

  

  While yes, big wheels are simply best as smaller wheels do equal smaller distance in the same amount of time or per unit for work. A larger axle increases acceleration, but requires more string per revolution. Smaller axle = Less string per turn which increases distance. Larger axle = More string per turn which decreases distance but increases acceleration. It's the same concept as the placement of door handles. Place the door handle on the outer end(as is normally done), and you have push the handle a further distance but it's easy. Place the door handle in the middle and you decreased the distance the door has to be pushed but increased the resistance.

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Thanks for submitting a tip for review!

• This is for speed, not distance. Don't be surprised if it doesn't go very far!

Advertisement

About This Article

Thanks to all authors for creating a page that has been read 244,507 times.

Did this article help you?

How Do U Make a Mousetrap Car Go Faster

Source: https://www.wikihow.com/Adapt-a-Mousetrap-Car-for-Speed#:~:text=Increase%20the%20size%20of%20the%20axle.&text=In%20other%20words%2C%20you%20should,and%20a%20larger%20driving%20wheel.

Share this post